Overhead Door is one of the oldest names in the industry (they invented the upward-acting garage door in 1921), and their openers are all over Bay Area garages – especially the Odyssey 1000 belt drive, the Legacy 696CD / 650 chain drive, and the Destiny 1200. Overhead Door and Genie share engineering, so many parts and programming steps overlap. One Stop Garage Doors & Gates repairs all Overhead Door openers and doors. We’re an independent service company, not a manufacturer dealer. Call 650-910-6090.

Common Overhead Door Model Faults
- Odyssey 1000 – Grinding, No Movement – The Odyssey belt drive is quiet by design, so grinding usually means a worn gear or sprocket assembly. Belt tension and the carriage are the next things we check.
- Legacy 696CD / 650 – Clicking or Dead – Legacy chain drives commonly fail at the logic board or the drive gear. A rapid clicking with no movement typically points to the gear kit.
- Destiny 1200 – Won’t Close, Light Flashing – A flashing light on Destiny units almost always signals the Safe-T-Beam safety sensors are blocked or misaligned, not an opener fault.
- Remotes Won’t Program – Overhead Door uses rolling-code systems shared with Genie (Intellicode). Generation mismatch is the usual reason an off-the-shelf remote refuses to pair.
- Wall Console Unresponsive – A dead wall button with working remotes is normally a wiring break at the staple or a failed console, both quick fixes.
- Opener Runs Then Reverses – Travel limits or force settings have drifted, or the door itself is binding. We check the door balance before touching the opener settings.

Odyssey, Legacy & Destiny Repair
We repair the models actually installed around here – Odyssey 1000 belt drive, Legacy 696CD and 650 chain drive, and Destiny 1200 – down to the gear kit, logic board, capacitor, carriage, and Safe-T-Beam sensors, rather than defaulting to a full replacement.

Overhead Door Doors Too
Beyond openers, we install and repair Overhead Door garage doors, match sections for panel replacement where the series is still available, and fit correctly-rated springs to the actual weight of the door.
Overhead Door Services
Model-aware repair for the openers and doors Overhead Door actually sells:
Odyssey 1000 Repair
Belt-drive gear kits, carriages, boards, and belt tension corrected on the Odyssey series.
Legacy 696CD / 650 Repair
Chain-drive gear assemblies, logic boards, and sprockets replaced on Legacy units.
Destiny 1200 Repair
Travel limits, force settings, boards, and Safe-T-Beam sensors diagnosed and repaired.
Safety Sensor Service
Blocked, misaligned, or miswired safety beams realigned so the door closes reliably.
Remote & Keypad Programming
Correct-generation rolling-code remotes and keypads paired to your unit.
Door Repair & Panel Matching
Overhead Door sections matched and replaced, with springs sized to the door.
Not sure which model you have? The label is usually on the side or back of the motor housing – send us a photo and we will identify it and bring the right parts. Call 650-910-6090.
Why Choose Us
Licensed Santa Clara Gate Technicians
Fast, Same-Day Response
A broken gate is a security risk, so we prioritize gate calls across Santa Clara. Call and you speak with a real team member who dispatches a technician right away.
Licensed & Insured
One Stop Garage Doors & Gates is a licensed California contractor (#1143915). Every technician is trained on residential and commercial gate systems.
Every Gate Type & Brand
Sliding, swing, electric, iron, and wood gates — plus operators from LiftMaster, DoorKing, Viking, FAAC, Elite, and US Automatic.
Our Google Reviews
Overhead Door Repair Pricing
*Starting estimates — not final prices. Gate repair cost depends on gate type, operator brand, and parts. Call 650-910-6090 for a firm quote before any work begins.
Frequently Asked Questions
Yes – Odyssey 1000, Legacy 696CD and 650, Destiny 1200, and older Overhead Door units, plus their garage doors. We’re an independent service company, not a manufacturer dealer.
Unplug the unit for about 30 seconds to power-cycle it. For a full reset, hold the program/Learn button on the motor until the indicator goes out – note this clears all remotes, so they’ll need reprogramming.
The Odyssey is a belt drive and normally very quiet, so grinding usually means a worn gear or sprocket assembly. Gear kits are replaceable, so this rarely requires a new opener.
Most often the Safe-T-Beam safety sensors are blocked, misaligned, or have a damaged wire. Clean the lenses and realign until both indicators are steady.
They share engineering and rolling-code technology, so many parts and programming procedures overlap. That’s why a technician who knows both can service either.
On a label on the side or rear of the motor housing. Send us a photo of it and we’ll confirm the model and the parts needed before we come out.
Often yes, where the series is still produced. We match panel design, texture, and color as closely as available and replace only the damaged section.
Usually, if the unit is under roughly 12 years old – gear kits, boards, and sensors are all affordable replacements. Beyond that, or with a failed motor, replacement is the better value.
Yes, and other major brands. Openers are largely interchangeable, so we’ll fit whichever suits your door and budget and program everything before we leave.
Need Gate Repair in Santa Clara?
Same-day service is usually available. Upfront pricing, no surprise fees.
License: 1143915














